0 |
TMR |
Transceiver
Multi
Receive |
M+A
M+A+B
M+A+B+C
etc. |
Allows monitoring of any
combination of channels shown on the display.
If signal received, RX stays on Freq. |
|
1 |
STEP |
Frequency Step Size Setup |
2.5 to
25. kHz |
2.5, 5, 6.25, 10,
12.5, 25
kHz |
|
2 |
SQL |
Squelch Level |
00 > 09
|
10 squelch levels
00
= minimum / normally open |
|
3 |
TXP |
Transmit Power |
High |
Full Power |
|
Low |
Reduced Power |
4 |
AUTOLK |
Keypad Lockout |
ON |
Keypad Lock ON at Power up |
|
OFF |
Keypad Lock OFF at Power up
Press [*] for 2 secs to Lock/Unlock |
5 |
TOT |
TX Time Out Timer
|
15 > 600 secs
|
15 second steps |
|
6 |
APO |
Auto Power Off |
30, 60 >
300
minutes |
Time Set that radio will
Power Off after last signal received. |
|
OFF |
Turn off APO Option |
7 |
WN |
Bandwidth |
Wideband |
25.0 kHz |
|
Narrowband |
12.5 kHz |
8 |
ABR |
LCD Backlight Timer |
1 > 50
secs |
Backlight duration = 1 > 50 |
|
OFF |
Disables 1 > 50 second timer.
Backlight remains ON. |
9 |
BEEP |
Keypad Voice Prompt |
ON / OFF |
Turn ON / OFF keypad voice
prompt |
|
10 |
R-DCS |
Receive - Digital
Coded Squelch |
D023N >
D754I |
Squelch opens when proper DCS
code is detected |
|
OFF |
No DCS code required |
11 |
R-CTCS |
Receive - Analog
Tone Squelch |
67.0 >
254.1 Hz |
Squelch opens when proper
CTCSS tone detected |
|
OFF |
No CTCSS tone required |
12 |
T-DCS |
Transmit - DCS
Code |
D023N >
D754I |
Transmits specified code |
|
OFF |
No DCS code transmitted |
13 |
T-CTCS |
Transmit - CTCSS
Code |
67.0 >
254.1 Hz |
Transmits specified tone |
|
OFF |
No CTCSS tone transmitted |
14 |
DTMFST |
Determines when DTMF
signal tones/codes are heard through speaker |
OFF |
No DTMF tone heard |
|
DS-ST |
Only manually keyed DTMF codes are heard |
ANI-ST |
Only automatically keyed DTMF codes are heard |
DT+ANI |
All DTMF codes are heard |
15 |
BCL |
Busy Channel
Lockout |
ON |
Prevents transmit if active
signal on the channel |
|
OFF |
No lockout |
16 |
SC-ADD |
Add Scan Channel |
ON |
Add channel to scan list |
|
OFF |
Remove channel from scan list |
17 |
SC-REV |
Scan Resume Method |
TO |
(Time Operation) Scan stops when signal detected.
The scan resumes after approximately 5 seconds
(even if the channel is still active). |
|
CO |
(Carrier Operation) Scan stops when signal detected.
Scan resumes when signal disappears. |
SE |
(Search Operation) Scan stops when signal detected.
Scanning will not resume. |
18 |
OPTSIG |
Optional
Signaling |
OFF |
No optional signaling |
|
DTMF |
DTMF signaling selected |
2TONE |
2TONE signaling selected |
5TONE |
5TONE signaling selected |
19 |
SPMUTE |
Speaker Mute
Settings |
QT |
Squelch opens for CTCSS/DCS tones only. |
|
AND |
Squelch opens when CTCSS/DCS
tone is recognized along with the optional signaling. |
OR |
Squelch opens when
either the CTCSS/DCS tone OR the optional
signaling is recognized. |
20 |
PTT-ID |
PTT ID - When to
send |
OFF |
Do not send |
|
BOT |
Send at Beginning of
Transmission |
EOT |
Send at the End of
Transmission |
BOTH |
Send at both Beginning and
End |
21 |
PTT-LT |
PTT ID - Transmit Delay |
0 > 30 |
Set Delay Time before transmitting PTT-ID |
|
22 |
S-INFO |
Auto Group Dialing |
Group
Signal Code Memory |
1 > 15
Can only be set with software |
|
23 |
EMC-TP |
Alarm Mode |
OFF |
Turn
OFF Alarm Mode |
|
ALARM |
Turn on Alarm sound |
ANI |
Send Alarm code and ID code |
BOTH |
Both of the above |
24 |
EMC-CH |
Alarm Channel |
000 >
199 |
Specified Alarm Channel |
|
25 |
SIG-BP |
Signal Beep
2TONE/5TONE
Alert Tone |
ON |
Receive Alert Tone ON |
|
OFF |
Alert Tone OFF |
26 |
CHNAME |
Channel Name Edit |
In Channel Mode,
edit the Current Name |
|
27 |
CA-MDF |
Channel
A
Display Mode |
FREQ |
In Channel Mode,
display the selected format in display A |
|
CH |
NAME |
28 |
CB-MDF |
Channel
B
Display Mode |
FREQ |
In Channel Mode,
display the selected format in display B |
|
CH |
NAME |
29 |
CC-MDF |
Channel C
Display Mode |
FREQ |
In Channel Mode,
display the selected format in display C |
|
CH |
NAME |
30 |
CD-MDF |
Channel D
Display Mode |
FREQ |
In Channel Mode,
display the selected format in display D |
|
CH |
NAME |
31 |
LANGUA |
Language |
English |
Screen and Voice |
|
Chinese |
32 |
SYNC |
Display Sync |
OFF |
Separate A/B channel
display. |
|
AB |
Synchronizes
display AB, CD, or AB+CD
This allows the upper
display to show channel name while the lower
shows the frequency. |
CD |
AB +
CD |
33 |
MAINFC |
MAIN
Foreground Color |
Select
Color |
Black
White
Red
Blue
Green
Yellow
Indigo
Purple
Gray |
|
34 |
MAINBC |
MAIN
Background Color |
Select
Color |
|
35 |
MENUFC |
MENU
Foreground Color |
Select
Color |
|
36 |
MENUBC |
MENU
Background Color |
Select
Color |
|
37 |
STA-FC |
STA
Foreground Color |
Select
Color |
|
38 |
STA-BC |
STA
Background Color |
Select
Color |
|
39 |
SIG-FC |
SIG
Foreground Color |
Select
Color |
|
40 |
SIG-BC |
SIG
Background Color |
Select
Color |
|
41 |
RX-FC |
MAIN
Foreground Color |
Select
Color |
|
42 |
TX-FC |
MAIN
Foreground Color |
Select
Color |
|
43 |
TXDISP |
Transmit Display |
POWER |
Display Power Level |
|
MIC-V |
Display Mic Audio Level |
44 |
MEM-CH |
Memorize Channel |
000 > 199 |
Indicates channel number to
be stored. |
|
45 |
DEL-CH |
Delete Channel |
000 > 199 |
Indicates channel number to
be deleted. |
|
46 |
SFT-D |
Frequency Shift
Direction |
OFF |
No Offset (simplex) |
|
+ |
Plus frequency shift |
- |
Minus frequency shift |
47 |
OFFSET |
Frequency Shift
Offset Amount |
00.00
> 999.99 |
Frequency shift in MHz |
|
48 |
ANI |
ANI ID Code |
Can only be set
with software |
|
49 |
ANI-L |
ANI Length |
3, 4,
5 |
Length of ANI ID code |
|
50 |
REP-S |
Repeater
Activation Tone |
1000Hz 1450Hz
1750Hz 2100Hz |
Audible tone for
repeater activation |
|
51 |
REP-M |
Repeater
Forwarding Mode |
OFF |
Function OFF |
|
CARRI |
Forward after receiving
Carrier |
CTDCS |
Forward after receiving
correct CTDCS |
TONE |
Forward after receiving
correct mono audio (Menu 42) |
DTMF |
Forward after receiving
assigned DTMF code (ANI) |
52 |
TMR-MR |
Dual Watch
Return Time Delay |
OFF |
Function OFF |
|
1 > 50
seconds |
This is the delay
time before returning to the primary channel
after secondary signal is clear. |
53 |
STE |
Squelch Tail Elimination
Requires both radios have function ON. |
OFF |
Function OFF |
|
ON |
Eliminates squelch tail at end of
transmission. |
54 |
RP-STE |
Repeater
Squelch Tail Elimination
Requires a repeater using this function.
|
OFF |
Function OFF |
|
1 > 10 |
Delay Time |
55 |
RPT-DL |
Repeater squelch tail delay.
|
OFF |
Function OFF |
1 > 10 |
Delay Time |
|
56 |
DTMF-G |
DTMF Gain /
Audio Level |
0 > 60 |
0 = Lowest Audio Gain
60 = Highest Gain |
|
57 |
M-GAIN |
Microphone Gain /
Audio Level |
0 > 127 |
0 =
Lowest Audio Gain
127 = Highest Gain |
|
58 |
SKIPTX |
Channel Randomization
Requires 2 Quad Radios |
OFF |
Function OFF (Normally OFF) |
|
SKIP1 |
Randomizes channel sequence. |
SKIP2 |
Sequentially skips to next
channel |
59 |
SC-MOD |
Automatic Scan Resume Method |
OFF |
Scan disabled with radio
reboot, menu key, or PTT |
PTT-SC |
Scan resumes after transmit
or menu operation |
MEM-SC |
Scan resumes after Power
Up. |
PON-SC |
Scan starts at Power On. |
|
60 |
RESET |
Initialize to Factory Defaults |
VFO |
Menu Initialization |
ALL |
Menu and Channel Initialization |
|