Baofeng UV-3R, UV-3R+
  
Programming Memories
Manually
 
   
These examples will guide you through the basic
manual programming of the UV3R+.
  
Set radio to VFO Mode
Press/Hold [U/V] key for approx 3 seconds. (Display will change)

Select VHF range
Press/Release the [U/V] key to switch between UHF (450 MHz) / VHF (150 MHz) range. Select the VHF range for this exercise.

Pull up knob on top of radio.
This will enable you to make menu selections.

Set Step Size to 5 kHz
Press/Release the [MENU] Key
The first [MENU] item to appear will be RXCODE or [MENU] #1
Rotate Dial clockwise until [MENU] #9 STEP appears.
Press/Release the [U/V] key.
Rotate Dial to select 5.00 (5KHz)
Press/Release the [U/V] key.
Press/Release the [MENU] key.
Frequency will once again appear.

Rotating the dial will now advance the frequency display in 5 kHz increments.
 
1 MHz Steps

To temporarily utilize 1 MHz increments:
 

Lift knob on top of transceiver
Press/Release the Function Key
Rotate Dial to change 1 MHz at a time
Press/Release the Function Key
 
 
Programming a Simplex Channel

Simplex is defined as Transmitting (TX) and
Receiving (RX) on the same frequency.

 
This example is for 146.520 MHz

 
Press/Release the [U/V] key to enter the VFO Mode.
 
Rotate Dial until “146.520” appears on the LCD screen.
Press/Release [F/ALERT] Button (left side)
Press/Release the [U/V] key.
A tiny channel number (1-99) will blink above the frequency display.
Rotate Dial to the desired channel number (1-99)
Press/Release the [U/V] key.

Frequency is now stored in that memory location.

Now, press and hold the [U/V] key to return to the VFO mode.
 
Programming a Repeater Channel

For this example, we will program the 146.700 MHz repeater.

 

For this example, we will program the 146.700 MHz repeater.
   146.700 MHz -
Repeater TX Freq
   146.100 MHz -
Repeater RX Freq
        (referred to as a minus -0.600 MHz offset)
   123.0 Hz -
CTCSS/PL Tone required to access repeater

Press/Release the [U/V] key to enter the VFO Mode.  

Rotate Dial until “146.700” appears on the LCD. (RX freq)
Press/Release [MENU] key.
Rotate Dial to [MENU] 10 (OFFSET)
Press/Release the [U/V] key.
Rotate Dial until “00.600” is displayed.
Press/Release the [U/V] key.

Rotate Dial to [MENU] 11 (SHIFT)
Press/Release the [U/V] key.
Rotate Dial until “-” (minus) is displayed.
Press/Release the [U/V] key.

Rotate Dial to [MENU] 2 (TXCODE)
Press/Release the [U/V] key.
Rotate Dial until “123.0” is displayed.
Press/Release the [U/V] key.

Press/Release [F/ALERT] Button (left side)
Press/Release the [U/V] key.
A tiny channel number (1-99) will blink above the frequency display.
Rotate Dial to the desired channel number (1-99)
Press/Release the [U/V] key.

Frequency is now stored in that memory location.


TOP of PAGE
 
Miklor Home
 


   


        US Sales and
    Warranty Support

 



Handheld
Radios

 

Mobile Radios
   
  

CABLES
FTDI CABLE

6 in 1 Cable
 
ACCESSORIES

BATTERIES
and
AA  CASES


ANTENNAS
Dual Band
and
220 MHz

 


POUCHES

    
SOFT CASE
 


TEST EQUIPMENT

   

  PIGTAILS

ADAPTORS

      
      

Study Guides
& Handbooks

 

HAM RADIO
for DUMMIES