outdoors hunting camping SHTF GMRS radio communications antenna battery electronics scanners digital computer software hardware laptop iPad iPhone eBay music radio
.

 

Programming Memories
Manually
 
BTech UV2501  UV2501+220  UV5001
KT8900  JT6188

 

 
 




Frequency Mode vs. Channel Mode

These two modes have different functions and often confused.

Frequency Mode (VFO) - Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.

Channel Mode (MR) - Used for selecting preprogrammed channels.

All programming MUST be initially done in the Frequency Mode only. From there you have the option of assigning the entered data to a specific channel for later access in the Channel Mode if desired.
 
Note" The Menu button on the microphone and F button on the radio serve the same purpose.
 
Videos

If you have any of the above models, there are programming videos available HERE.
 




Preliminary Display Appearance Setting
for Upper and Lower Display
 
(can be set in either VFO or MR mode)

Menu
29
[M]   Frequency 
Name
Channel
[M]   [EXIT]  Select the desired display appearance
for Upper Display
         
Menu
30
[M]   Frequency 
Name
Channel
[M]   [EXIT]  Select the desired display appearance
for Lower Display
         
 
 

Programming Repeater with Standard Offset

RX = 146.850 MHz
TX = 146.250 MHz
 
TX CTCSS tone 123.0
into channel 99
 
 
Set radio to VFO Mode  by pressing [V/M]
     Channel number at the right will disappear.
 
Menu
  37
[M] 9 9 [M]   [EXIT]  Delete Prior Data in channel
       
Menu
  13
[M] 123.0 [M]   [EXIT]  Select desired TX encode tone
         
 
Use  [A/B]  to select  Upper  display.
 
Enter     146850   Enter the Receive frequency
 
Use  [A/B]  to select  Lower  display.
 
Enter     146250    Enter the Transmit frequency
 
Use  [A/B]  to return to  Upper  display.
 
Menu
  36
[M] 99 [M]   [EXIT]  Enters the Receive channel
         
Use  [A/B]  to select  Lower  display
 
Menu
  36
[M] 99 [M]   [EXIT]  Enters the transmit channel
         
      [V/M]
 
Return to MR Mode
Channel number will re-appear.

 
 
 
Programming a Simplex Channel

446.000 MHz
into channel 99
 
Set radio to VFO Mode  by pressing [V/M]
     Channel number at the right will disappear.
 
Menu
  37
[M] 99  [M]   [EXIT]  Delete Prior Data in channel
         
      446000   Enter RX in upper display
Menu
  36
[M] 99  [M]   [EXIT]  Key in the desired channel
         
      [V/M]
 
Return to MR Mode
Channel number will re-appear.
 
 
 
Entering a Channel NAME
 
Set radio to Channel Mode (MR)  by pressing [V/M]
     Channel number will appear at the right.

 
Select the display that will show the channel's NAME.  (Upper or Lower)
This only needs to be done once.
 
Menu
  29
[M] NAME  [M]    [EXIT]  Changes Upper display to NAME
         
Menu
  30
[M] NAME [M]    [EXIT]  Changes Lower display to NAME
         

 
Entering the Name

 
Dial in channel to be changed.

-  Select   [MENU]  28  [MENU]   (The display will start flashing)
 
-  Use    keys  (or radio dial)  to select the desired character.
-  Press  [# Lock]  button on the keypad.
-  Repeat above until name field is complete.
 
-  Press  [MENU]  to Save.

 
 

TOP of PAGE
 
Miklor Home
 
Miklor
 


   


Support
Miklor

Support
Miklor